Enhanced TDS
Identification & Functionality
- Chemical Family
- Fillers Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Materials Features
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Color (Properties)
- Flame Rating
- Physical Form
- Mechanical Properties
Value Units Test Method / Conditions Tensile Modulus (Cond.) 8000 MPa ISO 527-1/-2 Tensile Modulus (Dry) 8300 MPa ISO 527-1/-2 Stress at Break (Cond.) 140 MPa ISO 527-1/-2 Stress at Break (Dry) 150 MPa ISO 527-1/-2 Strain at Break (Dry) 3 % ISO 527-1/-2 Tensile Creep Modulus (1000 H, Strain < 0.5%, at 23°C) (Cond.) 6400 MPa ISO 899-1 Flexural Modulus (Dry) 7500.0 MPa ISO 178 Flexural Strength (Dry) 210.0 MPa ISO 178 Charpy Unnotched Impact Strength (at 23°C) (Dry) 70.0 kJ/m² ISO 179/1eU Charpy Unnotched Impact Strength (at 23°C) (Cond.) 55.0 kJ/m² ISO 179/1eU Charpy Notched Impact Strength (23°C) (Dry) 8 kJ/m² ISO 179/1eA Izod Notched Impact Strength (Cond.) (at 23°C) 8 kJ/m² ISO 180/A Charpy notched impact strength (23°C) (Cond.) 7 kJ/m² ISO 179/1eA Izod Notched Impact Strength (Dry) (at 23°C) 9 kJ/m² ISO 180/A - Typical Properties
Value Units Test Method / Conditions Polymer Abbreviation (at 23°C) PA6T/6-GF25 FR(52) - - Density (at 23°C) 1380 kg/m³ ISO 1183 Viscosity Number (0.5% in 96% H₂SO₄) (at 23°C) 130 cm³/g ISO 307, 1157, 1628 Water Absorption (Equilibrium in Water, at 23°C) 5 - 6 % Similar to ISO 124 Moisture Absorption, Equilibrium (at 23°C/50% r.h) 1.1 - 1.5 % Similar to ISO 125 Bulk Density 0.7 g/cm³ - - Thermal Properties
Value Units Test Method / Conditions Deflection Temp. Under Load 1.8 Mpa (Hdt A) 220 °C ISO 75-1/-2 Service Temperature (Short Cycle Operation) max. 270 °C - Temperature Index at 50% Loss of Tensile Strength After 20000 H 125 °C IEC 60216 Temperature Index (at 50% loss of tensile Strength after 5000 H) 150 °C IEC 60216 Coefficient of Linear Thermal Expansion, Longitudinal (at 23°C - 80°C) 24.0×10⁻⁶ /K ISO 11359-1/-2 Coefficient of Linear Thermal Expansion, Transverse (at 23°C - 80°C) 67.0×10⁻⁶ /K ISO 11359-1/-2 Thermal Conductivity 0.31 W/(m K) DIN 52612-1 Specific Heat Capacity 1400 J/(kg*K) - - Electrical Properties
Value Units Test Method / Conditions Relative Permittivity (1 Mhz) (Dry) 4 - IEC 62631-2-1 Dissipation Factor (1 Mhz) (Dry) 200.0×10⁻⁴ IEC 62631-2-1 Volume Resistivity (Cond.) 1×10¹¹ Ohm.m IEC 62631-3-1 Volume Resistivity (Dry) 1×10¹² Ohm.m IEC 62631-3-1 Surface Resistivity (Cond.) 1×10¹³ Ohm IEC 62631-3-2 Comparative Tracking Index - CTI (Cond.) 600 - IEC 60112,Test LIquid A Electric Strength K20/K20, (60*60*1 mm³) (Cond.) 33 kV/mm IEC 60243-1 Electric Strength K20/K20, (60*60*1 mm³) (Dry) 37 kV/mm IEC 60243-1 - Shrinkage
Value Units Test Method / Conditions Molding Shrinkage (Normal) 1 % ISO 294-4 Processing Shrinkage, Constrained, Longitudinal (Tm = 320°C, Tw = 100°C) ⁴ 0.4 % - - Flammability
Value Units Test Method / Conditions Glow Wire Flammability Index - GWFI (at D < 0.75mm Thickness) 960 °C IEC 60695-2-12 Glow Wire Ignition Test - GWIT (at D = 0.75 mm Thickness) 775 °C IEC 60695-2-13 Oxygen Index 26.0 % ISO 4589-1/-2 - Processing Parameters
Value Units Test Method / Conditions Melting Temperature 295.0 °C ISO 11357-1/-3 /DSC - Injection Molding
Value Units Test Method / Conditions Melt Temperature (Range) 310 - 330 °C Mold Temperature (Range) 80 - 120 °C - Residence Time max. 5 min - Drying
Value Units Test Method / Conditions Moisture Content (Recommended) ¹ 0.01 - 0.04 % - Dryer Temperature ² 110 °C - Drying Time ³ 8 h - - Machine Settings
Value Units Test Method / Conditions Temperature Hopper Throat 80 °C - Cylinder Temperature 1 (Feed Zone) 300 °C - Cylinder Temperature 2 (Compression) 310 °C - Cylinder Temperature 3 (Metering - Zone, in Front of The Screw) 320 °C - Cylinder Temperature 4 (Nozzle) 320 °C - Peripheral Screw Speed max. 0.3 m/s - Processing Properties
Value Units Test Method / Conditions Melt Temperature (Injection Molding/Extrusion) 310 - 330 °C - Mold Temperature (Injection Molding) 80 - 120 °C - Molding shrinkage (Parallel) 0.55 % ISO 294-4 Molding Shrinkage³ (Constrained) 0.4 % Molding Shrinkage (Normal) 1 % ISO 294-4 - Note
- If product name or properties don't state otherwise.
- The asterisk symbol '*' signifies inapplicable properties.
- Test box with central gating, dimensions of base (107*47*1,5) mm, processing condition: TM = 320°C (unreinforced) or 330°C (reinforced), TW = 80°C
- Note
- If product name or properties don't state otherwise.
- The asterisk symbol '*' signifies inapplicable properties.
- Test box with central gating, dimensions of base (107*47*1,5) mm, processing condition: TM = 320°C (unreinforced) or 330°C (reinforced), TW = 80°C
Regulatory & Compliance
- Certifications & Compliance
- Quality Standards
Safety & Health
- Product Safety
y In case processing is done under conditions as recommended (cf. processing data sheet) melts are thermally stable and do not generate hazards by molecular degradation or the evolution of gases and vapors.
Like all thermoplastic polymers the product decomposes on exposure to excessive thermal load, e.g. when it is overheated or as a result of cleaning by burning off.
- Product Safety
In case processing is done under conditions as recommended (cf. processing data sheet) melts are thermally stable and do not generate hazards by molecular degradation or the evolution of gases and vapors.
Like all thermoplastic polymers the product decomposes on exposure to excessive thermal load, e.g. when it is overheated or as a result of cleaning by burning off.
- Safety Instructions
Provide suitable exhaust ventilation at the drying process and in the area surrounding the melt outlet of processing machines.
Closed containers should only be opened in well-ventilated areas. Ensure thorough ventilation of stores and work areas.
When incorrectly processing an unpleasant odour can be produced, especially when the recommended processing parameters are exceeded. Check
- Moisture content of pellets
- Melt temperature
- Residence time
When there is a strong odour, immediately check processing parameters, ventilate the area well and recheck moisturecontent of material. If necessary stop processing and redry the material.
Any short stoppages in production, it is recommended that you inject material into the mould not purge an air shot. It is advisable to dispose of purgings etc into water containers.
Packaging & Availability
- Packaging Information
Standard packs are bag and bulk container (octagonal IBC=intermediate bulk container made from corrugated board with a liner bag).
Other packaging materials and shipping in road or rail silo wagons are possible by agreement.
The containers should only be opened immediately before processing or drying.
- Packaging Information
Standard packs are bag and bulk container (octagonal IBC=intermediate bulk container made from corrugated board with a liner bag).
Other packaging materials and shipping in road or rail silo wagons are possible by agreement.
Storage & Handling
- Storage Information
The containers should only be opened immediately before processing or drying.
To ensure that the delivered product absorbs as little moisture as possible, the containers should be stored in dry rooms and always carefully closed again after partial quantities have been withdrawn. In principle, the product can be stored for a long period of time.
Containers stored in cold rooms should be equalized to ambient temperature before opening in order to avoid condensation on the granules.
Regardless of the storage conditions, the product should be pre-dried according to our recommendations and the machine should preferably be loaded using a closed conveyor system.
- Storage Information
To ensure that the delivered product absorbs as little moisture as possible, the containers should be stored in dry rooms and always carefully closed again after partial quantities have been withdrawn.
In principle, the product can be stored for a long period of time.
Containers stored in cold rooms should be equalized to ambient temperature before opening in order to avoid condensation on the granules.
Regardless of the storage conditions, the product should be pre-dried according to our recommendations and the machine should preferably be loaded using a closed conveyor system.